Strike Variable Optic Mount for Aimpoint® Micro Standard

$99.95

In stock

SKU

SI-T1-VOM-BK

The Strike Variable Optic Mount for Aimpoint® Micro Standard is a user-defined height optic mount. A mount option for the popular Aimpoint® Micro Standard footprint which is used on many red dots offered on the market. With a height range of 1/3 co-witness to a maximum of 1.93 inches, this mount allows for precise, incremental height adjustments via notches on the slider. When properly installed and torqued, this mount is also designed to maintain zero even after re-installation, giving you peace of mind. Made from lightweight and high-strength 6061-T6 aluminum and machined with precision, the Strike Variable Optic Mount for Aimpoint® Micro Standard is a user-defined height to configure you specific setup for your specific needs.

MOUNT COMPATIBILITY: 1913 Picatinny

NOTE: 1/3 co-witness height is only with Aimpoint® T-1/T-2/H-1/H-2 or other same optic housing height red dots

(See individually listed red dot compatibility and suggested hardware to use in PRODUCT SPEC tab)
RED DOT COMPATIBILITY: Aimpoint® Micro Standard

Torque: (Do not exceed)
-M5x28mm Socket Head: 35 in/lbs (4.00 nM) [Picatinny rail base mount]
-M4x20mm Socket Head 20 in/lbs (2.26 nM) [Optic mount plate]
-M3x4mm Rounded or hardware provided by manufacturer (recommended by optic manufacturer) [Optic mount screws]
-M3x6mm Rounded 15 in/lbs (1.69 nM) [Slider]
-M3x20mm Rounded 10 in/lbs (1.13 nM) [1.93" riser]

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Add to Wish List

PACKAGAGE CONTENTS:
-x1 Picatinny rail base mount (fully assembled)
-x1 Optic mount plate (fully assembled)
-x1 Slider
-x1 1.93" riser
-x4 Screw for Aimpoint® Micro Standard [M3x4mm T10 Rounded or hardware provided by manufacturer]
-x4 Screw for Slider [M3x6mm T10 Rounded]
-x4 Screw for 1.93" riser [M3x20mm T10 Rounded]
-x1 Torx tool [T10]
-x1 Torx tool [T25]
-x1 Hex tool [M4]
-x1 Loctite® Threadlocker Blue 243®
-x1 Warning card

PRODUCT FEATURES:
-User defined optic mount height for Aimpoint® Micro Standard
-Height ranges from 1/3 co-witness to 1.93” maximum
-Adjust height incrementally with notches on slider
-Repeat zero mount when re-installed
-Lightweight and high-strength
-Machined from 6061-T6 aluminum

PRODUCT SPECIFICATIONS

PICATINNY RAIL BASE MOUNT:
-LENGTH: 60.95mm (2.40")
-WIDTH: 20.00mm (0.79")
-HEIGHT: 12.88mm (0.50")
-WEIGHT: 1.70 oz

SLIDER:
-LENGTH: 47.97mm (1.90")
-WIDTH: 29.00mm (1.14")
-HEIGHT:15.96mm (0.63")
-WEIGHT:1.10 oz

1.93" RISER:
-LENGTH: 58.25mm (2.30")
-WIDTH: 20.40mm (0.80")
-HEIGHT: 15.41mm (0.60")
-WEIGHT: 0.70 oz

OPTIC MOUNT PLATE:
-LENGTH: 53.03mm (2.09")
-WID> 11.58mm (0.46")
-WEIGHT: 1.10 oz

DISCLAIMER: "Aimpoint" is a federally registered trademarks of Aimpoint Inc. and are one of many trademarks owned by Aimpoint Inc. Neither Strike Industries Inc nor this site are affiliated in any manner with, or otherwise endorsed by, Aimpoint Inc. The use of "Aimpoint" on this page is merely to advertise the sale of Aimpoint products. For additional genuine Aimpoint Inc and parts visit www.aimpoint.us.

-CALIFORNIA PROPOSITION 65 WARNING:-
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov

WARNING:
-The below compatibility list is based on known SI test fitments as well as footprint data found online but do not guarantee 100% the full list is accurate
-Please note there is also other possible red dot brand and model fitments that can work
-Be careful and use your best judgment on which hardware to use for your specific setup
-All installations should only be done by a certified professional gunsmith and properly tested to pass all safe and function tests

-AIMPOINT MICRO STANDARD: (+ additional Aimpoint Micro Standard footprint optics not listed here)

SIOPTO: SCOUTER